Blog Archives - Leisure Auto

What Is Driver Fatigue Detection System?

September 2, 2021/0 Kommentare/in Blog /by leisureautosafety

What is driver fatigue detection system? It is an automobile safety system that helps prevent traffic accidents caused due to the negligent driving of the driver becoming very drowsy. Various researches have indicated that up to 20% of all major road accidents worldwide are fatigue related, up to even 50% on some busy roads. Some studies also indicate that accidents caused due to tiredness and lack of concentration can kill someone in less than five minutes. This makes it extremely important for the driver to stay alert and not fall asleep at the wheel.

What is driver fatigue detection system used for? This is used on trucks, buses, taxicabs, limousines, delivery vehicles, as well as other commercial vehicles. The system works on the principle of a simple push button that senses if the driver becomes very drowsy and needs to take some rest. Once the button is pushed, a special device sends out a series of signals to a central computer. Once the system senses that the driver is already extremely sleepy, it immediately alerts the control center to send the driver to a sleep center or other rehabilitation center.

The system monitors the condition of the drivers while they are working. There are several factors which can affect the working condition of the drivers. The use of an automobile security system is one of the most effective ways of avoiding such accidents from taking place. However, there is no fool proof way of avoiding accidents completely. The use of driver fatigue detection system is one of the most effective ways of avoiding such hazards. When the system detects that the driver is falling asleep, it immediately alerts the control center.

There are various reasons due to which the automobile security system automatically alerts the center regarding the falling asleep condition of the drivers. One of the reasons can be attributed to the excessive use of the handheld computer by the drivers while driving. This excessive use of the handheld device is what is used in monitoring their progress. The monitor also records all the activities of the drivers through the video footage. When this video footage is analyzed at the center, it is able to easily determine whether the driver is falling asleep or not.

The use of driver fatigue detection system is also helpful in determining whether the driver is using the automobile too much. If the driver is overworked beyond its capacity, it automatically alerts the center for one reason or another. Once the operator realizes the load he/she has to carry, it automatically puts the driver into a restful mode.

Another reason for which such a system is used to monitor the activities of the drivers is the violation of road rules. Many times, the traffic rules are ignored by the drivers. Usually, the drivers do not understand the meaning of these traffic rules. Such a system helps in knowing the rules and follows them strictly. The use of what is driver fatigue detection system alerts the center about such actions of the drivers which causes the center to issue a fine if the drivers are not able to follow the rules.

What is an Advanced Driver Assistance System?

September 2, 2021/0 Kommentare/in Blog /by leisureautosafety

What is an advanced driver assistance system? It is a group of computer technologies that help drivers in parking and driving functions using a secure interface. ADAS enhance vehicle and road security through a user-friendly, robotic interface.

It was introduced to the US market in 1992 by the American Automobile Association (AAA). The purpose of the advanced driver assistance system was to develop a safer and easier interface between drivers and vehicles. Its development has so far involved the use of advanced driver information system (ADIS), which uses a number of sensors to monitor a specific area. ADAS can be used to detect objects and animals in the road as well as to detect vehicles and their speed.

The system is designed so that all the controls are accessible to the driver by using a touch screen. The system monitors the location of the vehicle, the speed of the vehicle and other variables. Based on the readings, a number of different functions are activated, such as adjusting the brake lights and adjusting the steering wheel locks.

The main disadvantage of the advanced driver assistance system is that it only monitors for the safety purposes mentioned above. It does not deal with issues such as maintaining good mileage or maintaining the right balance of fuel efficiency between the engine and the vehicle. ADAS has also been criticized for not having any effect on reducing drunk driving. However, this seems to be a major shortcoming considering that drunk drivers account for a large part of traffic accidents. The installation of these systems may help reduce accidents due to drunk driving but further research is needed to prove this.

The advance driver assistance system comes in two versions, the base and the premium version. Both versions are similar in function but differ in price. The base package is meant for regular vehicles. These come with basic features such as the anti-lock brakes system, the vehicle tracking system, the speedometer and others. Premium packages go beyond these basics by including additional safety features such as traction control, the vehicle stability control and the car’s electronic Stability Assist. All the advanced driver assistance systems include these additional features.

There are many manufacturers that manufacture these systems. Most of these companies offer online websites where a potential buyer can view the features of each brand of these systems. A potential customer can make his or her own decision based on specifications, cost and features. A customer who is not satisfied with the performance of the system has the option to return the product or ask for a refund. An advanced driver assistance system can greatly improve the driving experience for the individual.

What Does the Driver Fatigue Monitor do?

September 2, 2021/0 Kommentare/in Blog /by leisureautosafety

So you have a company whose maintenance department has developed a new driver monitoring device. The new gadget is supposed to help truck drivers to keep track of their balky joints. However, it doesn’t seem to be doing much. Or maybe it’s working against them. Read this article to find out what does the driver fatigue monitor do?

It does tell the driver that he or she is experiencing more fatigue as time goes on. But the monitor doesn’t tell them why they are experiencing more balky joints. It’s just telling them that their work is causing it. And this is all it does.

If the driver does not get some rest, then balky joints will continue to plague him and eventually he will go down even further. That will lead to even more fatigue. Eventually the truck driver may go completely sick and not know why. This can lead to a big accident on the road.

The truckers family is at risk because they are also working longer hours. The longer they truck, the more wear and tear on the body. The longer they truck, the more hours they expose themselves to toxic fumes and other harmful chemicals in the air. They also put themselves at greater risk of heart disease and stroke. So even if the monitor tells them that they are feeling better, what they really need is some rest.

You might think it’s impossible to find rest when your mind is telling you that you need it. You could take a vacation or you could let yourself go for a little bit. The problem with letting yourself go is that, while you are gone, your balky, tired truck is going to grind forward at a much faster pace. If the driver is not properly rested, then the truck will not be as safe to drive.

It’s important to keep a close watch on how your drivers are doing. This is one of the best ways to find out what does the driver fatigue monitor do. While this device is very helpful, it cannot do everything for you. You have to stay on top of your drivers and make sure they are getting enough rest to recover and do their job properly. Rest is important, especially for those who have been on the road for so long.

If you find that your driver has been overworked, try giving them some down time. Not only will it give them a chance to rest, but it will also make sure that he/she is alert. You should also try to give your drivers a break once in a while. This is especially important if they have been driving for a long period of time. Your driver needs to rest, but you also need your driver to work as hard as possible!

One of the best devices out there for tracking rest is called RestARocks. They have an application that is installed right onto the truck. All you need to do is make sure that your drivers are in the truck and that the monitor is connected before you begin using the software. The software has many features including an e-mail alert if the driver takes a nap. With what does the driver fatigue monitor do, it can really help your business to save money and make sure that you’re getting the most out of your drivers!

How to Manage Driver Fatigue – Effective Techniques

September 2, 2021/0 Kommentare/in Blog /by leisureautosafety

When it comes to being tired, how to manage driver fatigue is important. Being tired is the first sign that something is wrong. In today’s hectic world, there is simply no way around it – being overworked can have serious consequences. And while some companies have started offering paid breaks to their workers, this is not always the best solution. It may give the employee a short term break, but in the long run they are not better able to handle the work that they are given. Therefore, the best thing to do is understand how to manage driver fatigue and avoid the problems that it can cause.

So what is driver fatigue exactly? Simply put, it is being tired while driving, which puts drivers at risk for accidents. Fatigue is also one of the leading causes of workplace accidents. It is especially dangerous for younger drivers, teenagers, and people in middle age. Even when a business adheres to strict hours of operation, there still is a greater responsibility towards the general motoring public and its driver to avoid fatigue and its dangers. There are a number of simple ways to make sure that you do not become a victim of tiredness while driving.

One of the simplest ways to prevent fatigue from setting in while driving is to ensure that you are well rested before starting work. This can be achieved by having a good night’s sleep and eating a light snack earlier in the day. Another way of making sure that you do not get too much fatigue is to make sure that you are as physically fit as possible. Some physical fitness activities that you can undertake include jogging, walking, or swimming, whilst doing some light housework or garden tasks. If you are in poor health, such as diabetes, cancer or a weak heart, you should seek out medical advice first before undertaking any physical activity.

Of course, there are other factors that contribute to fatigue among motorists on the road. For instance, the weather can play a big part in how to manage driver fatigue. Heavy snow or ice may keep drivers working for several hours at a time. However, this will only make it more difficult for them to control their vehicle, as they may become fatigued much faster than usual. Similarly, wind can also affect how well a driver manages his vehicle, as some can become confused and have a hard time keeping their vehicle under control during strong winds.

However, there are also certain things that can affect how well a driver can drive without getting tired. For instance, an irregular work schedule, such as being caught up in traffic for long periods of time, may affect how well a driver can function during their daily driving duties. Likewise, a poor diet can also cause a lack of energy for a driver, which can lead to fatigue. Some of these things may seem minor or trivial, but can actually be very harmful to one’s health on the road.

To prevent fatigue, drivers should always stay aware of how they are feeling as they drive. They should also make sure that they are not overloading their vehicles or using heavy fuel loads unnecessarily. Drivers should also ensure that they are taking the proper precautions to ensure that they are driving safely, such as installing safety and protection devices on their vehicles and ensuring that they are not drinking and driving. As well, drivers should make sure that they do not consume alcoholic beverages before they set out on a drive. All of these things can be effective methods of how to manage driver fatigue safely and effectively.

Special fleet management for Wuxi dairy transport team

Mai 11, 2021/0 Kommentare/in Blog /by leisureautosafety

Wuxi dairy cold chain transportation team is responsible for the transportation of dairy products in major supermarkets in Wuxi City. In order to ensure the fresh quality of the transported goods, the team operates from 17:00 a.m. to 9:00 a.m. the next day and has no rest all year round. The team urgently needs to solve the following problems:
The driver works for a long time and is in a state of fatigue
Drivers’ bad driving behavior, frequent accidents and increasing insurance premium year by year
The in car equipment can not be integrated, and the supervisors need to view multiple functional platforms
The driver finds someone to lead the shift without evidence control
Aiming at the user’s problems, the scheme of LS860 fleet management is adopted to monitor the comprehensive environmental information of “person vehicle road”, which realizes driver identity comparison, driver fatigue status monitoring, driving behavior monitoring and analysis, lane deviation warning, forward collision avoidance warning, temperature monitoring of transport compartment and vehicle position monitoring.

After using this system for a period of time, the bad driving habits of drivers are effectively improved, and the accident rate of the fleet is reduced by 30%; The supporting background of the product not only has remote safety monitoring function, but also has basic information management function such as vehicle and driver. During the operation of the product, it can obtain the corresponding vehicle information and driver information in real time, including vehicle location, speed, driver information, driving status, etc., so as to realize unified and standardized operation management.

If you are looking for reliable OEM ADAS BSD manufacturer, please feel free to email [email protected], we will offer professional & customized ASAS BSD solution at reasonable price.

Help smart city – bus passenger flow statistics system covers Yinchuan, Ningxia

Mai 11, 2021/0 Kommentare/in Blog /by leisureautosafety

LS860 bus passenger flow statistics system covers nearly 2000 buses in Yinchuan city. With the advantages of high-precision products, it provides scientific basis for the dispatching and operation management decision-making of Yinchuan bus. It helps the bus companies to arrange the departure time and time interval reasonably, compile the timetable, implement the driving plan, and improve the decision-making ability, so as to realize the scientific scheduling of the bus and make full use of the public resources.

Yinchuan project adopts the mode of “passenger flow statistics + electronic stop sign + mobile app” to push the number of people getting on and off the bus and in the bus at each bus stop to the electronic stop sign and mobile app in real time. It is convenient for the public to know the arrival time of the bus, the number of passengers on the bus and the degree of congestion in the bus in real time. The public can reasonably arrange the travel time and choose the appropriate means of transportation in time to reduce the travel waiting time.

By analyzing the historical data of bus passenger flow statistics, the management department can grasp the passenger flow distribution law of each time period, line and station, judge the rationality of existing line setting, and provide the basis for line adjustment. Scientific line equipment and reasonable vehicle scheduling can effectively alleviate urban traffic congestion, improve the image of the city, and improve the satisfaction of urban travelers.

If you are looking for reliable OEM ADAS BSD manufacturer, please feel free to email [email protected], we will offer professional & customized ASAS BSD solution at reasonable price.

The application of 79g millimeter wave radar and 24g millimeter wave radar in ADAS

April 15, 2021/0 Kommentare/in Blog /by leisureautosafety

The application of 77g millimeter wave radar and 24g millimeter wave radar in ADAS

In the field of automobile safety, millimeter wave radar, as one of the three sensing technologies of automatic driving, plays an important role. What are the similarities and differences between 79g millimeter wave radar and 24g millimeter wave radar in the application of ADAS?

1. From the perspective of cost, the cost of 24g millimeter wave radar is lower than that of 79g millimeter wave radar;
2. The range of 24GHz radar is short, and that of 79GHz radar is long (up to 150-200m). Therefore, 24g millimeter wave is generally installed on the side and tail of the car, which is mainly used for blind area anti-collision alarm (BSD), lane change assistance (LCA), door opening assistance and reversing anti-collision alarm. 79g millimeter wave can be installed in the front or side of the car, which is generally used for front anti-collision warning and automatic anti-collision alarm Cruise control (ACC), intelligent braking (AEBS) and lateral vehicle warning.
3. Compared with 24g millimeter wave radar, 79g millimeter wave radar has longer detection range, better range resolution, smaller detection volume and wider detection angle.
4. In terms of installation and debugging, 24g millimeter wave calibration is easier than 79g millimeter wave calibration, and 79g calibration is more complex.
5. The wavelength of 79g millimeter wave radar is shorter than that of 24g millimeter wave radar, and there are many more antennas. Therefore, only a few of them need to be installed on the key detection points of the car to achieve good results.
6. Leisure Auto 79g millimeter wave radar is a scheme for large vehicle safety management, which is suitable for more than 99% of the vehicle models on the market.

If you are looking for reliable OEM ADAS BSD manufacturer, please feel free to email [email protected], we will offer professional & customized ASAS BSD solution at reasonable price.

Difference between blind spot detection(BDS) and radar sensor

April 15, 2021/0 Kommentare/in Blog /by leisureautosafety

In the wave of the continuous development of intelligent driving, more and more intelligent devices are applied to different vehicles, the purpose is to better assist the driver in daily driving. Blind area is a big hidden danger of high incidence of vehicle accidents, so many drivers will install blind area detection equipment in their cars. Today, I would like to introduce the difference between the two commonly used blind area detection equipment.

Vehicle radar sensor

1. Objective: to protect vehicles from being scratched by obstacles;
2. It is impossible to distinguish pedestrians from common obstacles, and there is no difference in alarm, so drivers are prone to fatigue and reduce their vigilance;
3. It can only be triggered in specific scenes, such as left turn, right turn, reversing and so on. It can not be monitored when the driver forgets to turn on the turn signal or when driving straight.

Blid Spot Detection system(BSD)

1. Objective: to protect pedestrians from being crushed by vehicles;
2. It can automatically distinguish pedestrians and common obstacles, and only alert pedestrians to avoid blind area accidents;
3. It can identify common road pedestrians, such as pedestrians on foot, cyclists and motorcyclists;
4. It works continuously from ignition to flameout to provide pedestrian collision warning for drivers, which can prevent collision accidents when vehicles start;
5. When a pedestrian is identified, the driver is reminded to slow down and give way inside the vehicle, the pedestrian is reminded to give way outside the vehicle, and the two-way reminder improves the timeliness of giving way.

If you are looking for reliable OEM ADAS BSD manufacturer, please feel free to email [email protected], we will offer professional & customized ASAS BSD solution at reasonable price.

This paper is to understand the differences of blind area monitoring, lane change assistance, blind area on the side of vehicle and lane offset

April 15, 2021/0 Kommentare/in Blog /by leisureautosafety

On the Internet, a consumer who bought accord posted a post saying that when he bought a car, he saw a blind area image system on the configuration table. He thought that he wanted a blind area monitoring system with an alarm light on the rear-view mirror to remind the driver. But after he bought the car, he found that it was not the same thing. He wanted to install a blind area monitoring system, which was very embarrassing.

Indeed, in the wave of the continuous development of intelligent driving, more and more intelligent driving subsystems are configured on the car. Not to mention that ordinary consumers can fully understand the functions and functions of these intelligent driving subsystems, even an intelligent driving Engineer may not be able to fully understand them.

Simply speaking from the aspect of lane change, there are different kinds of system names, such as blind spot monitoring system, lane change assistant system, parallel assistant system, Lane departure system and vehicle side blind area image system. If you only look at the name, you are totally confused. You can’t tell which name is the function you want.

For these kinds of systems used in lane changing, I will first classify them, and then classify them to explain the basic functions, which will help you better understand and choose the system you want. According to whether the system has alarm sound, the lane changing intelligent driving system is divided into two categories, as shown in the figure below.

1.Side blind area imaging system

The vehicle side blind area image system uses the camera installed at the designated position on the vehicle to capture the surrounding environment of the vehicle that the driver cannot see, and automatically displays it on the central control screen after reaching the trigger condition (generally turning on the turn signal).

Note: in the side blind area display system, there are two systems with the same name but different functions. Is it the same side blind area imaging system? There is such a big difference in functions that you have to see it clearly when you buy a car

2. Blind area monitoring system (parallel line auxiliary system) and lane changing auxiliary system

Before introducing the system, first popularize the GB 15084-2013 motor vehicle indirect vision device performance and installation requirements about the field of vision requirements of automobile rear-view mirror: the shaded part in the figure is the field of vision that the rear-view mirror needs to see.For the standard text requirements, I won’t do too much interpretation here. I will reconstruct this figure in combination with the size of passenger cars. The length of a general passenger car is 4.5-5.0 meters. After deducting the driver’s 2.25-2.5 meters from the rear of the car, the starting position of the field of vision of the rearview mirror is about 1.5-1.75 meters from the rear of the car, as shown in the following diagram.

It can be seen that a large part of the field of vision outside the rear-view mirror is the driver’s blind area. Combined with the ISO 17387 standard, the area on the rear side of the vehicle is divided into two areas: blind area monitoring and lane change assistance. This leads to the difference between blind area monitoring system and lane changing auxiliary system
Blind area monitoring system: it monitors whether there are obstacle vehicles in the 3M * 5.5m area behind the left and right sides of the vehicle. When there are obstacle vehicles, the blind area monitoring alarm light will give an alarm, and the driver can’t perform the steering action at this time.

Lane changing assistant system: it monitors whether there are potential dangerous vehicles in the area 3 * 30m behind the vehicle blind area, calculates the collision time according to the relative speed of the vehicle and self vehicle in the lane changing assistant area, and warns the driver whether there is danger when turning according to the collision time.
For the parallel line auxiliary system, it is the alias of the blind area monitoring system, and its function is completely consistent with the blind area monitoring system.

3. Lane departure system
Lane departure system uses the camera installed on the windshield of the vehicle interior rearview mirror to identify the lane line information. When the driver unconsciously (without turning signal) deviates from the lane, the system will emit a beep alarm sound, and the instrument will display which side of the lane line the vehicle deviates from.

If you are looking for reliable OEM ADAS BSD manufacturer, please feel free to email [email protected], we will offer professional & customized ASAS BSD solution at reasonable price.

Five years of technical training, innovation and technology to create ADAS quality brand!

April 8, 2021/0 Kommentare/in Blog /by leisureautosafety

Guide: since last year, leisure auto has launched different series of advanced intelligent driving assistance system (ADAS) products for the aftermarket, 4S shop, front market, car factory and electronic manufacturer, which has attracted the attention of many businesses and car owners in the industry, and has been favored by many people. What is the charm of leisure auto ADAS?

Advanced intelligent driving assistance system (ADAS) has been used in foreign countries for many years, and there are a lot of data to prove its role in reducing the driving accident rate. At present, European and American countries all force automobile manufacturers to install ADAS technology on their automobile products, and only vehicles with ADAS technology can get the highest 5-star safety standard.

Although ADAS technology has been widely used in foreign cars, because of technology research and development and other reasons, few people know ADAS, and it has not been well popularized. With the development of intelligent vehicle and driverless technology, people pay more and more attention to safe driving. ADAS technology is in great demand in China. On March 7, 2017, the Ministry of transport organized and formulated the transportation industry standard safety technical conditions for operating passenger cars (JT / t1094-2016, hereinafter referred to as JT / T 1094 standard), which was formally implemented on April 1, 2017. In the standard, it is required that the operating buses over 9 meters must have lane departure warning and front collision warning (FCW), and the transition period of 13 months is given.

In 2012, several co founders of leisure auto started the ADAS project. At that time, there was no domestic enterprise that developed and produced ADAS technology. Through exchanges with many senior people in the automotive industry, domestic and foreign research and market analysis, and long-term attention to driverless technology, the co founders found such an opportunity of huge demand for ADAS technology in the domestic market. Set up R & D team to develop ADAS belonging to Chinese people. In the five years of technology development process, leisure auto products are gradually taking shape. It has launched different series of intelligent driving assistance system (ADAS) products for the aftermarket, 4S shop, front market, car factory and electronic manufacturers, which are concerned by many businesses and car owners in the industry and favored by many people

2012 “leisure auto ADAS system” design revolution storm

Driving safety is just a need, and it is the most concerned thing of every driver and every family. Globally, the leader of ADAS industry is Mobileye company of Israel. Its products are reliable in performance but expensive. They are only suitable for European and American markets and can not meet the needs of developing markets. To this end, with the dream of developing cost-effective ADAS products suitable for Chinese people, leisure auto team began to develop a high-speed vehicle platform with independent intellectual property rights in 2012. After repeated failures and continuous attempts, leisure auto ADAS system, a newly hatched pupa, broke out of the cocoon.

2013 “Pride auto ADAS system” trial production

In 2013, the team developed the basic model a based on DSP, combined with a number of auxiliary chips and special components, and carried out a large number of tests in Guangzhou Radio Group, electronic technology research and development (Shanghai) Co., Ltd. and Dalian Hualu Panasonic laboratory according to the requirements of vehicle specifications. Then, according to the prototype design, the team guided the pilot production of 600 sets in the Dandong factory of alpai club, And send to the sample car factory for testing.
2014: the upgraded a + model was successfully developed and made an amazing debut
In 2014, the upgraded a + model was developed on the basis of a model, and passed the vehicle specification test in Guangzhou Radio Group. With the cooperation of Neusoft group, the two products were tested on the road and in the real situation for a long time, and the samples were sent to the vehicle factory for testing.

2015 Excellent quality creates order legend

In May 2015, the upgraded a + intelligent driving assistance system was tested and adjusted in Yutong Bus Factory for about six months. In just three months, it won the order of Yutong Bus front loading market and successfully won the long-term supplier of its front loading market.
Leisure auto starts new mileage and focuses on Aftermarket
After winning the first supply order of Yutong Bus within three months after its establishment, leisure auto started a new journey.
In July, on the basis of the smooth development of automobile front loading market, we focused on the automobile rear loading market which has not been fully explored. In addition to all the advantages of the original function design of ADAS system, it also catered to the world trend of “small car becoming luxury car”, so that Volkswagen car can have “never lax co driver” like luxury car —-Adas advanced driving assistance system brings car users the same driving quality as luxury cars.
Leisure Auto “leisure Auto” Intelligent Technology Co., Ltd. officially launched
In March 2015, on the basis of successful product development, technical backbones took advantage of the heat and began to formally plan to set up a company to fulfill their dream of automobile driving safety. In this way, “leisure Auto” came into being.

2016 inheriting the vitality of the brand, personal mobile app officially entered the test

Inheriting the vitality and glory of the new brand leisure auto, the new smart phone afterloading app has officially entered the technical test. It enables individual car users to receive the warning from ADAS system in time through mobile phone while driving, and remind drivers to take corresponding protective measures.
The new smart phone afterloading app not only carries the excellent vitality of the new brand, but also boldly challenges and innovates under the premise of uncertain market prospect of automobile afterloading, striving to seek better technical guarantee for driving safety of individual automobile users.
At present, in the domestic ADAS market, Mobileye has the largest front loading coverage. Because it is expensive and not close to the people, it can not be widely promoted in the short term. This gives domestic ADAS enterprises a valuable opportunity, and leisure auto caters to this opportunity to launch its own series of products. Beyond Mobileye, every leisure auto people take this as their goal: independent R & D ; R & D is the way out for domestic ADAS enterprises to develop and grow. Only through R & R & D of ADAS with independent intellectual property rights can they stand in the market. Only in this way can the domestic ADAS industry get healthy development, and can they really go to the world and compete with Mobileye in the market.

If you are looking for reliable OEM ADAS manufacturer, please feel free to email [email protected], we will offer professional & customized ASAS solution at reasonable price.

What Is Driver Fatigue Detection System?

What is an Advanced Driver Assistance System?

What Does the Driver Fatigue Monitor do?

How to Manage Driver Fatigue – Effective Techniques

Special fleet management for Wuxi dairy transport team

Help smart city – bus passenger flow statistics system covers Yinchuan, Ningxia

The application of 79g millimeter wave radar and 24g millimeter wave radar in ADAS

Difference between blind spot detection(BDS) and radar sensor

Vehicle radar sensor

Blid Spot Detection system(BSD)

This paper is to understand the differences of blind area monitoring, lane change assistance, blind area on the side of vehicle and lane offset

1.Side blind area imaging system

2. Blind area monitoring system (parallel line auxiliary system) and lane changing auxiliary system

Five years of technical training, innovation and technology to create ADAS quality brand!

2012 “leisure auto ADAS system” design revolution storm

2013 “Pride auto ADAS system” trial production

2015 Excellent quality creates order legend

2016 inheriting the vitality of the brand, personal mobile app officially entered the test

Unsere Produkte

Schnelle Links

Kontakt